Designed for the galley wall of a Mercedes-Benz Sprinter van, this cabinet gives your microwave a permanent place alongside everyday kitchen storage. A dedicated microwave bay sits beside an enclosed compartment, with one internal shelf creating two storage levels for dishes, food, and daily gear. A 0.6" ultralight Paulownia plywood body in Pastel Sage pairs with 0.6" natural bamboo doors. Concealed joinery keeps exposed screws and visible fasteners out of sight for a clean finish on every side. Integrated ventilation slots above the microwave bay give warm air an escape path while preserving the built-in look. Confirm your appliance dimensions and required ventilation clearances before ordering. The microwave is not included. The storage door closes with a black push-button travel latch and stays supported while open by a flap-stay lifter. The cabinet arrives fully assembled, with a pre-wired 12V LED strip underneath to brighten your galley.

This kitchen brings a familiar, home-like finish into your campervan with white Shaker-style fronts and a warm bamboo counter. The cabinet measures 43.9" W × 17.1" D × 36.5" H with its facade. Extend the fold-out table panel for additional preparation space, reaching up to 54.6 inches wide, then fold it away when you need the aisle clear.A 0.59-inch Paulownia plywood body keeps unnecessary cabinet weight down, paired with a 0.6-inch bamboo countertop. The prepared sink opening gives you a starting point for your plumbing setup. The sink and faucet are not included.Three pantry shelves sit behind a Shaker-style door with a push-knob latch. A lower drawer keeps utensils and everyday items close at hand, while a dedicated cooktop drawer provides space for a compatible appliance, sold separately.A tall storage bay with its own pull-out offers flexible room for larger gear. Confirm dimensions and ventilation before fitting an appliance. The cabinet ships fully assembled and ready to mount, with concealed joinery for a clean exterior without exposed screws or visible fasteners.

Designed for the Ford Transit 148WB cab, this tapered cabinet gives documents, small gear, and everyday essentials a home above the dash. The dimension render shows 61" W × 24" D × 16" H. One door opens to a single wide shelf, keeping stored items together and out of sight.The body is built from 0.59-inch plywood and finished in New Pine gel stain on maple. A bright white interior shelf makes stored items easier to see, while the wood-grain exterior brings warmth to your van interior.A full-overlay hinge set and touch-latch closure provide access through the single door. Cam-lock hardware, wooden dowels, and reinforced support strips are incorporated into the cabinet’s assembled construction.The tapered shape follows the cab roofline. The cabinet arrives fully assembled and ready to mount; confirm structural mounting points and seated clearance for your installation. This model does not include LED lighting.

Smart Space-Saving Cabinet, Built to Fit Your Campervan PerfectlyDesigned for the Ford Transit 148WB galley wall, this fully assembled 37-inch cabinet combines a left-side microwave bay with right-side storage. An open upper cubby keeps everyday items accessible while parked, and an enclosed lower compartment sits behind a lift-up door.A 0.59-inch lightweight plywood body pairs with a 0.69-inch MDF Shaker-style door, both finished in Stormy Sea. Concealed joinery keeps exposed screws and visible fasteners out of sight for a clean exterior.A round push-button travel latch secures the storage door. The concealed full-overlay hinge and flap-stay lifter support it when open, while a pre-wired 12V LED strip underneath lights the counter or living area below.The center partition separates the microwave bay from the storage section. The microwave is not included. Confirm the appliance dimensions, usable bay opening, mounting method, and ventilation requirements before ordering.The cabinet arrives fully assembled and ready to mount. Position it, secure it to structural mounting points, connect the lighting, and install your microwave according to its manufacturer’s instructions.

Designed for the galley wall of a Ford Transit 148WB, this fully assembled 37.2-inch overhead cabinet turns unused wall space into organized storage. Two independent lift-up Shaker doors open to two compartments, each with upper and lower shelving, for dishes, pantry items, coffee supplies, and daily gear.The cabinet combines a 0.59-inch ultralight Paulownia plywood body with 0.69-inch MDF Shaker doors. A matching Stormy Sea finish gives your galley a coordinated look while the lightweight construction keeps unnecessary cabinet weight down.Push-button travel latches secure both doors, while flap-stay lifters support them when open. A flush-mounted 12V LED strip underneath provides task lighting across the galley counter.Concealed hardware and joinery keep exposed screws and visible fasteners out of sight. The cabinet arrives fully assembled and ready to mount, so installation focuses on positioning, structural mounting, and connecting the lighting.

Designed for your Ford Transit campervan, this kitchen brings the main cabinet, open storage bay, rear panel, and extended bamboo countertop together in one coordinated unit. A step-bridging base accommodates the Transit floor step; dry-fit it to your finished floor before securing the cabinet.The main section has shelved storage behind a Shaker-style door, with a drawer above for smaller items. Beside it, an open-front bay with its own pull-out drawer provides flexible storage for gear or an accessory that fits your layout.A 0.59-inch Paulownia plywood body in slate blue pairs with a 0.69-inch bamboo countertop. The prepared sink opening includes a removable bamboo cover, while the folding side table adds counter space when needed. Sink and faucet are not included.The whole unit arrives fully assembled, with hinges, drawer slides, locks, and mounting brackets included. Installation focuses on positioning, checking the floor-step fit and clearances, and securing the kitchen to your van’s structure.

The Vankea Refrigerator Cabinet combines an upper refrigerator bay and two lower storage drawers in one 20.9-inch-wide footprint. Built around the Sprinter 170, its curved, tapered plywood body is finished in Pastel Sage and measures 75.0" H × 20.9" W × 26.9" D.The fixed appliance platform supports a refrigerator bay above the drawer storage. Confirm the usable internal opening with Vankea and compare your chosen refrigerator’s dimensions, door travel, and ventilation requirements before ordering. Exterior cabinet measurements do not establish appliance fit. The refrigerator is not included.Two drawers with 0.59-inch natural bamboo fronts organize cookware, pantry items, and daily gear below. Each uses a 16-inch undermount slide and its own round push-button travel lock. Close and secure both drawers before driving.The cabinet arrives fully assembled and ready to mount, with concealed connectors and structural fastening points for a clean exterior. Position, level, and secure the tower to your van’s structure, then install the refrigerator separately according to its manufacturer’s requirements.

The Slim Tall Storage Cabinet puts a narrow interior position to work. Engineered around the Sprinter 170, it measures 11.5 inches across the front and 75 inches tall, creating vertical storage for pantry goods, clothing, towels, or daily gear.A 0.59-inch ultralight plywood body has curved, tapered sides designed around the Sprinter wall profile. The Pastel Sage finish pairs with two stacked 0.59-inch natural bamboo doors for a warm, clean appearance.Inside, one fixed shelf and two adjustable shelves create up to four storage sections. Reposition the adjustable shelves as your needs change. Each door opens independently on full-overlay hinges with a touch-latch closure.A two-slot upper ventilation panel supports passive airflow at the top. Internal connectors, dowels, structural screws, and steel brackets form the assembled construction, while concealed joinery keeps visible fasteners off the exterior.The cabinet arrives fully assembled and ready to mount. Confirm its wall profile and dimensions against your finished interior, then position, level, and secure it to structural mounting points.

Family dinners in the campervan can feel like home, while nighttime brings a comfortable full-size sleeping platform. This integrated dinette system converts from a practical dining setup into a bed in seconds. It is built from lightweight 0.59-inch Paulownia plywood, reducing cabinet weight by approximately 37% compared with standard builds without sacrificing strength or durability. The two opposing benches each measure 57.8 inches long by 24.6 inches deep by 17.3 inches high and create an installed span of approximately 69 inches. Add cushions or a full-size mattress to create a continuous sleeping surface. Each bench features soft-close hinged-top panels with recessed brass finger pulls. The panels open smoothly to reveal ventilated storage compartments for a fresh-water tank, heating equipment, electrical components, tools, and other gear. Multiple louvered cutouts and access points help maintain airflow, reduce moisture buildup, and keep installed systems accessible for routine maintenance. Two additional upper lids use heavy-duty butler-tray hinges. To convert the dinette into sleeping mode, open these lids and rest them securely on the integrated wooden support steps on the opposite bench. This creates a unified, level base for your cushions or mattress. During the day, place your dinette table between the benches to create a comfortable dining and gathering area. At night, remove the table, open the upper lids onto the supports, and arrange your cushions or mattress across the complete platform. Premium details include a white primed finish, natural wood trim accents, recessed brass pulls, heavy-duty hardware, soft-close panels, and integrated louvered ventilation. The complete system arrives fully assembled and ready to secure inside your van, combining seating, sleeping, and organized equipment storage without wasting valuable floor space.

Family dinners in the campervan can feel like home, with a comfortable full-size sleeping platform ready when night falls. This integrated white dinette system combines three functions in one carefully planned footprint: daytime dining, a convertible bed, and organized underneath storage. Built from lightweight 0.59-inch Paulownia plywood, the two opposing benches measure approximately 58 inches wide by 17 inches high and extend to an overall length of about 69 inches when positioned in the van. The lightweight construction reduces weight by approximately 37% compared with standard builds without sacrificing practical strength or durability. Each bench features secure soft-close hinged-top panels with recessed brass finger pulls. Beneath the tops, fully ventilated compartments provide organized space for a compatible fresh-water tank, heating system, electrical equipment, tools, and travel gear. Multiple louvered cutouts and access points promote passive airflow, help reduce moisture buildup, and keep installed systems accessible for routine service. Two additional upper lids use heavy-duty butler-tray hinges. To convert the dinette for sleeping, remove the table, open the upper lids, and rest them securely on the integrated wooden support steps on the opposite bench. The panels bridge the aisle to create a unified, level surface for your cushions or suitably sized mattress. During the day, place your dinette table between the benches for a comfortable space to eat, work, or relax. At night, deploy the integrated panels and add your cushions or mattress to complete the sleeping setup. Premium details include a white primed finish, natural wood trim accents, soft-close hardware, heavy-duty butler-tray hinges, recessed brass pulls, integrated support steps, and louvered ventilation throughout. The complete bench system arrives fully assembled and ready to mount, requiring only positioning and secure attachment to your vehicle structure.

This complete kitchen brings natural bamboo fronts and a Pastel Sage body into your Sprinter campervan. The coordinated run measures 85" W × 20" D × 37" H, with a fold-out table for extra counter space when you need it.The 0.59-inch Paulownia plywood body keeps unnecessary cabinet weight down, paired with a 0.69-inch bamboo facade and full-length countertop. A prepared sink position gives you a starting point for your plumbing setup. Sink, faucet, and cooktop are not included.Dedicated cooktop space sits alongside a sink station with under-sink shelving. A tall pull-out column brings deeper storage within reach, while a drawer pantry on undermount slides keeps everyday kitchen items organized.The kitchen ships fully assembled and ready to mount, with full-overlay hinges, a dedicated pull-out slide, push-button latch locks, and L-bracket construction. Concealed joinery keeps exposed screws and visible fasteners out of sight for a clean, coordinated finish.

Designed for the living area of your Campervan, this cabinet gives a compact microwave a permanent place so you don't have to choose between appliance space and storage for everyday kitchen gear. The left section is sized for a compact 0.7 cu. ft. microwave, while the cabinet beside it gives you enclosed storage for dishes, food, coffee gear, or other everyday items. Inside the storage section, the inclusion of two shelf levels allows you to separate and organize your everyday items effectively, making better use of the cabinet height than a single large, open compartment. A gel-stained wood body keeps the natural grain visible, adding warmth and contrast around the clean white front. Above the microwave bay, integrated ventilation slots provide a direct airflow path for warm air to escape from the appliance area. The cabinet arrives fully assembled and ready to install, with a lightweight 0.59-inch plywood body, Shaker-style MDF front, concealed hardware, a push-knob travel latch button, flap-stay door support, and an integrated 12V LED strip underneath.

Designed for the galley wall of your campervan, this cabinet gives everyday kitchen gear an organized home. Two independent lift-up compartments sit side by side, each with upper and lower shelving, so you can separate dishes, food, coffee gear, and daily items.A Carbon Gray gel-stained wood body keeps the natural grain visible around the clean white front. The 0.59-inch lightweight plywood body adds practical storage without unnecessary cabinet weight.0.69-inch MDF Shaker doors bring a familiar cabinet style into your van. Supplied in white paint-ready primer, the fronts can be finished to match your interior. Concealed hardware and joinery keep exposed screws and visible fasteners out of sight.The cabinet arrives fully assembled and ready to install. Round push-button travel latches secure each door, flap-stay lifters support the doors while open, and an integrated 12V LED strip underneath brightens the galley.

Family dinners in the campervan can feel like home, with a comfortable sleeping platform ready when night falls. This Stormy Sea dinette system provides three functions within one carefully organized footprint: a proper dining setup, an approximately 69-by-58-inch sleeping platform, and accessible storage for water, shower, electrical, and travel equipment. For dining, position your table between the two opposing benches to create a functional area for meals, work, or relaxing inside your campervan. Each bench measures approximately 57.7 inches long, 24.6 inches deep, and 17.3 inches high. Both benches are built from 0.59-inch lightweight Paulownia plywood with a Stormy Sea finish and natural bamboo detailing on the rear exterior access doors. Each bench features split hinged-top panels with recessed pulls cut directly into the plywood, providing convenient access to the ventilated storage compartments underneath. Louvered ventilation cutouts along the bench faces and end panels help promote passive airflow around stored equipment. The left bench provides flexible storage for a compatible fresh-water tank and shower setup. Integrated water-level viewing points let you visually check the remaining water when a compatible translucent tank is installed behind them. This keeps the water system organized while allowing the level to be checked without opening the entire bench. At the rear of the left bench, a dedicated exterior shower area remains directly accessible from outside the van. A rear exterior access door, finished with natural bamboo and fitted with a push-button lock, provides convenient access to the shower compartment, plumbing equipment, or smaller stored items. The bamboo adds warmth and contrast to the Stormy Sea bench body while giving the exterior access point a clean, finished appearance. The right bench provides organized storage for compatible batteries, inverters, wiring, electrical equipment, tools, and other campervan gear. The space can be arranged around the owner's equipment and installation requirements. The bench system is securely constructed with cam-lock joinery, flap hinges, full-overlay door hinges, recessed pulls, and push-button locks. These components support the bench structure, hinged-top panels, fold-out sleeping sections, and exterior access doors. When evening comes, remove or lower your dinette table as required and unfold the integrated panels across the aisle. The panels bridge the space between the two benches to create a continuous sleeping surface approximately 69 inches by 58 inches. Arrange custom cushions or a suitably sized mattress over the platform to complete the sleeping setup. This bench set arrives fully assembled and ready to install, requiring only positioning inside the van and secure attachment to the vehicle structure. It combines organized storage for water, shower, power equipment, tools, and travel gear with comfortable dining and a convertible sleeping platform in one compact campervan setup.

Designed for your campervan, this kitchen brings storage and counter space together in one compact footprint. A sink-side section with shelves and partitions organizes the core of your kitchen, while the fold-out bamboo counter adds work surface only when you need it, then folds flat to restore aisle clearance.Shaker-style drawers and door with black knobs keep everyday kitchen gear close at hand. A narrow side pull-out provides a separate place for taller items, and a hidden low compartment makes use of storage space near the base.The bamboo counter brings natural grain and warmth to the white cabinetry. A prepared sink opening lets you plan your plumbing and choose a compatible sink. The sink and faucet are not included.Built from 0.59-inch plywood, the cabinet has a white finish and concealed joinery for a clean exterior without exposed screws or visible fasteners. It arrives fully assembled and ready to mount, so installation focuses on positioning, checking clearances, and securing it to your van’s structure.

This complete galley brings white Shaker-style cabinetry and a warm bamboo countertop into your Sprinter. The dimension render labels the set 80" W × 39" D × 28" H. A 0.59-inch Paulownia plywood body provides practical storage while keeping unnecessary cabinet weight down.Four coordinated sections form the run: a two-door base cabinet, single-door base cabinet, two-door sink base, and four-drawer storage cabinet. Together, five doors and four drawers give cookware, pantry supplies, and everyday utensils their own places.The 0.6-inch bamboo countertop runs the full length of the set and includes a prepared sink opening. Cabinetry is supplied white-primed and paint-ready, with MDF Shaker-style facades. Full-overlay, soft-close door hinges provide controlled closing, while round black push-button hardware completes the fronts.The set ships fully assembled and ready to mount, with cabinet hardware installed. Sink, faucet, cooktop, refrigerator and other appliances, plumbing, electrical and gas components, and van-mounting hardware are not included.