01 / Microwave bay
A dedicated spot for your microwave
A built-in opening with ventilation above. Check your appliance dimensions and clearances; microwave sold separately.
Product detailsSmart Space-Saving Cabinet, Built to Fit Your Campervan Perfectly
Designed for the galley wall of a Mercedes-Benz Sprinter van, this cabinet gives your microwave a permanent place alongside everyday kitchen storage. A dedicated microwave bay sits beside an enclosed compartment, with one internal shelf creating two storage levels for dishes, food, and daily gear.
A 0.6" ultralight Paulownia plywood body in Pastel Sage pairs with 0.6" natural bamboo doors. Concealed joinery keeps exposed screws and visible fasteners out of sight for a clean finish on every side.
Integrated ventilation slots above the microwave bay give warm air an escape path while preserving the built-in look. Confirm your appliance dimensions and required ventilation clearances before ordering. The microwave is not included.
The storage door closes with a black push-button travel latch and stays supported while open by a flap-stay lifter. The cabinet arrives fully assembled, with a pre-wired 12V LED strip underneath to brighten your galley.
Main features
Designed around your day.
Thoughtful details, already built in.
02 / Two-level storage
Open up. Find what you need.
One internal shelf creates two storage levels. A flap-stay lifter holds the door open while you reach for daily essentials.
03 / Push-button latch
Press to open. Secure for travel.
A black push-button latch secures the storage door. Press to release the handle; press again to latch it flush.
04 / 12V task lighting
Light where you need it
Pre-wired 12V lighting brightens your galley below. The underside strip follows the cabinet’s built-in lighting route.
ConstructionMaterials
- ✓Cabinet body: 0.6" ultralight Paulownia plywood
- ✓Body finish: Pastel Sage
- ✓Doors: 0.6" natural bamboo
- ✓Joinery: concealed, with no exposed screws or visible fasteners
- ✓Door hardware: concealed full-overlay hinge and inside flap-stay lifter
- ✓Latch: black push-button travel latch
Lightweight build. Natural warmth.
The 0.6" ultralight Paulownia plywood body keeps cabinet weight down. Pastel Sage pairs with 0.6" natural bamboo doors for a warm, considered finish.
Clean from every angle
Concealed joinery keeps exposed screws and visible fasteners out of sight. Full-overlay concealed hinges preserve the tidy exterior.
Ventilation, built in
Slots above the microwave bay give warm air an escape path without extra vent hardware on the face. Follow your microwave manufacturer’s clearance requirements.
Dimensions
Product dimensions
In the boxWhat's included
- ✓Fully assembled cabinet with dedicated microwave bay
- ✓Enclosed storage with one shelf creating two levels
- ✓Concealed hinge, flap-stay lifter, and black push-button latch
- ✓Pre-wired underside 12V LED strip
- ✓Microwave not included
SpecificationsBuilt to these numbers
144 Sprinter39.2 × 16.1 × 15.4 in
170 Sprinter44 × 16 × 15.4 in
VehicleMercedes-Benz Sprinter camper conversions
Cabinet body0.6" ultralight Paulownia plywood
Body finishPastel Sage
Doors0.6" natural bamboo
Microwave bayDedicated opening with ventilation slots above
StorageOne internal shelf; two storage levels
Door hardwareConcealed full-overlay hinge and inside flap-stay lifter
LatchBlack push-button travel latch
LightingPre-wired 12V LED strip underneath
Total LED strip lengthApproximately 82.7" (engineering BOM)
AssemblyFully assembled and ready to install
FitmentCompatibility
Mercedes-Benz Sprinter144 & 170 wheelbasesOverhead wall mounting
Designed for the upper galley wall, swivel-seat area, or living-space wall in your Sprinter conversion. Select your wheelbase above to see the matching dimensions.
144 Sprinter: 39.2 × 16.1 × 15.4 in
170 Sprinter: 44 × 16 × 15.4 in
Confirm space and secure structural mounting points for your layout before ordering.
InstallationBefore you install
Medium difficulty2 peopleAbout 1 hour
Fully assembled. Ready to install.
No panels to assemble or doors to hang. Position the cabinet, secure it to structural mounting points, connect the 12V lighting, and fit your microwave.
Tools to have ready
- Power drill & drill bits
- Rivet nut tool
- Screwdriver
- Measuring tape & level